Results 1 to 9 of 9

Thread: Wheel bearing play

  1. #1
    Senior Member Ribrickulous's Avatar
    Join Date
    06.08.20
    Location
    Brooklyn, NY, USA
    Posts
    1,440
    Thanks Thanks Given 
    416
    Thanks Thanks Received 
    312
    Thanked in
    253 Posts

    Wheel bearing play

    Well, that’s worrying!



    Thankfully I’ve got an extra, but will certainly be using some retaining compound


    - 1972 CL350
    - 1985 VF700F
    Ed
    1972 CL350 K4
    1985 VF700F

  2. #2
    Administrator LongDistanceRider's Avatar
    Join Date
    05.22.20
    Location
    Vancouver, Washington USA
    Posts
    7,886
    Thanks Thanks Given 
    1,231
    Thanks Thanks Received 
    2,453
    Thanked in
    1,924 Posts
    That's not good
    Jim O'Brien
    1979 CM400T aka the Roadbike, 1978 CB400T1 semi restored, 1972 CL350K4 restoration and the 1971 SL350K1 disaster zone.
    Plus 2 SL350K0's , 2 SL350K1's, 1 CL350K0 and 1 CL350K1 waiting for space and time
    Contact: 408-239-9580 or [email protected]

  3. #3
    Senior Member Ribrickulous's Avatar
    Join Date
    06.08.20
    Location
    Brooklyn, NY, USA
    Posts
    1,440
    Thanks Thanks Given 
    416
    Thanks Thanks Received 
    312
    Thanked in
    253 Posts
    You’re telling me!

    I’m confident in the 635 retaining compound but you bet I’ll be checking in on that early next season.

    The other bearing was solidly locked in place.


    - 1972 CL350
    - 1985 VF700F
    Ed
    1972 CL350 K4
    1985 VF700F

  4. #4
    Benevolent Dictator ancientdad's Avatar
    Join Date
    05.21.20
    Location
    Nature Coast, FL
    Posts
    16,314
    Thanks Thanks Given 
    2,692
    Thanks Thanks Received 
    4,067
    Thanked in
    3,197 Posts
    You could make some punch divots inside the area where the outer race sits before using the retaining compound to help make it a little tighter, kinda like knurling
    (move along, nothing to see here)

  5. #5
    Senior Member mike in idaho's Avatar
    Join Date
    06.17.20
    Location
    Orofino Idaho USA
    Posts
    866
    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    280
    Thanked in
    245 Posts
    I've done that several times on truck and log trailer hubs over the years, the bearing race is usually loose again, next time you have it apart. JB weld might be a better choice for something with that much movement.
    '66 CL160
    '66 CB160
    '67 CL77
    '79 XS650
    '69 T100R
    '68 TR6R
    '69 T120R
    '72 750 Commando

  6. #6
    Senior Member Ribrickulous's Avatar
    Join Date
    06.08.20
    Location
    Brooklyn, NY, USA
    Posts
    1,440
    Thanks Thanks Given 
    416
    Thanks Thanks Received 
    312
    Thanked in
    253 Posts
    Yikes - how do you get it off after? The retaining compound I know can be removed with heat or some solvents.

    JB weld is just force it till it gives?


    - 1972 CL350
    - 1985 VF700F
    Ed
    1972 CL350 K4
    1985 VF700F

  7. #7
    Senior Member mike in idaho's Avatar
    Join Date
    06.17.20
    Location
    Orofino Idaho USA
    Posts
    866
    Thanks Thanks Given 
    1
    Thanks Thanks Received 
    280
    Thanked in
    245 Posts
    You don't need to get it off, unless you plan on riding enough miles to wear out a set of wheel bearings.
    '66 CL160
    '66 CB160
    '67 CL77
    '79 XS650
    '69 T100R
    '68 TR6R
    '69 T120R
    '72 750 Commando

  8. #8
    Sensei 66Sprint's Avatar
    Join Date
    05.22.20
    Location
    Roanoke, Virginia
    Posts
    2,012
    Thanks Thanks Given 
    16
    Thanks Thanks Received 
    945
    Thanked in
    617 Posts
    IF you consider that a properly torqued axle in a correct assembly prevents ANY axial movement, you may find the 635 sufficient to keep the wheel rotating on the bearing's ball rollers rather than independently rotating on the outer race of the bearing......It is going to "give" at the easier path first.....
    Contact info :
    For e-mails; [email protected]

    To send donations to the cause or towards my phone bill by PayPal, please use [email protected] to identify my account....
    Please include your vintagehondatwins username so I know to whom to send a thank-you ....

    Phone: (540)-525-5199

  9. #9
    Senior Member Ribrickulous's Avatar
    Join Date
    06.08.20
    Location
    Brooklyn, NY, USA
    Posts
    1,440
    Thanks Thanks Given 
    416
    Thanks Thanks Received 
    312
    Thanked in
    253 Posts
    Quote Originally Posted by mike in idaho View Post
    You don't need to get it off, unless you plan on riding enough miles to wear out a set of wheel bearings.
    Ah, gotcha. You never know, I like to keep things re-buildable


    - 1972 CL350
    - 1985 VF700F
    Ed
    1972 CL350 K4
    1985 VF700F

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •